Description

SimBooth Kit 2

The SimBooth Kit 2 is a complete, turnkey golf simulator bundle built around the larger SimBooth 2 enclosure. It is designed for clubs, teaching bays, and higher-end home installs that need more width, height, and screen size without having to source components from multiple vendors.

You get a heavy-duty aluminum enclosure, full-surface raised floor, half walls, a crease-free impact screen, and a 32” × 54” × 2” commercial hitting mat, plus the full tech stack: the IDRA II overhead launch monitor, BenQ AH30ST Full HD short-throw projector, and a 1-year GSPro membership.

The enclosure is approximately 12’1” wide × 12’ deep × 8’9” high, with recommended room space around 14’ W × 16’ D × 9’7” H or larger for comfortable swings and projector throw.

Everything ships together so a capable team of 3–4 people can install it in a few hours and be ready to tee off the same day.

Product Features

Product Features

What's Included

What's Included

• SimBooth Kit 2 enclosure
  • Includes aluminum frame, solid black panels, left and right half walls, and ceiling panels.

• Full-surface floor system
  • Includes modular floor panels and integrated hitting mat cut-out.

• Commercial hitting mat
  • Approximately 32" x 54" x 2".

• Impact screen
  • Crease-free, low bounce-back screen with 16:10 ratio.

• IDRA II AI overhead launch monitor
  • Includes integrated light and required cabling.

• BenQ AH30ST Full HD projector

• Projector beam / mount
  • Designed for structure-mounted projector installation.

• GSPro golf simulator software – 1-Year Membership
  • Auto-renews after year 1 unless cancelled.

• Required cabling
  • Includes HDMI, USB, and power cables.
• Basic hardware and tools for assembly
  • Includes bolts, nuts, washers, wing nuts, and Allen keys.
• Basic installation instructions and documentation

Product Specifications

Product Specifications

Enclosure & Room Specs

Tech & Software

Getting Started Guide

Getting Started Guide

1. Verify your room size
   • Measure your space and confirm it meets or exceeds the recommended minimum room dimensions.
   • Make sure there is clear swing space for your longest club and no overhead obstructions.
2. Plan layout and PC location
   • Decide where the SimBooth 2 will sit in the room and where your PC will be located.
   • Confirm access to power outlets and network connections.
3. Unpack the crate
   • Open the shipping crate and sort components into groups: structure panels, floor panels, half walls, screen, mat, IDRA II, projector, beam, hardware, and cables.
4. Pre-stage components
   • Bring all parts into the final room before assembly so you do not need to move the completed structure later.
   • Lay ceiling and wall panels roughly in position on the floor to visualize assembly.
5. Review the installation guide
   • Read through the SimBooth installation instructions before starting so you understand the sequence: ceiling, walls, floor, then tech.
6. Assemble the frame on the floor
   • Follow the guide to connect ceiling sections and upper wall frames while they are still lying flat.
7. Install lower panels and bracing
   • Attach lower wall panels and any structural braces that stiffen the enclosure before raising it.
8. Raise the enclosure
   • With your helpers, tilt and lift the assembled frame upright into its final position.
   • Check that all sides are straight, level, and square.
9. Install the screen and floor
   • Mount the impact screen while keeping tension even around the perimeter.
   • Lay floor panels and install the hitting mat so everything is flat and flush with the screen edge.
10. Mount IDRA II and projector
    • Attach the IDRA II launch monitor to its overhead mounting location.
    • Install the projector beam and mount the BenQ projector at the approximate recommended distance.
11. Connect PC, power, and cables
    • Run HDMI from PC to projector, and USB / network from PC to IDRA II.
    • Use cable clips or Velcro ties to keep everything neat and out of swing paths.
12. Install GSPro and configure
    • Install GSPro and any required IDRA II software or launchers.
    • Log in, pair the launch monitor, and confirm that shots are registering.
13. Fine-tune and test
    • Adjust projector zoom, focus, and keystone so the image fills the screen.
    • Hit test shots and adjust camera / launch monitor settings for accurate ball flight and distances.

Product Installation Guide

Product Installation Guide

1. Gather tools and helpers
   • Plan on 3–4 adults to safely lift and align panels.
   • Have basic tools ready, including socket set or wrenches, screwdrivers, tape measure, level, ladders, and step stools.
2. Assemble the ceiling frame
   • On the floor, connect the ceiling frame pieces using the supplied bolts, washers, and nuts.
   • Confirm all joints are tight and the frame is square.
3. Attach upper wall panels
   • Bolt upper side and rear wall panels to the ceiling frame.
   • Check alignment and correct any gaps before tightening hardware fully.
4. Install lower wall panels and braces
   • Attach lower wall panels to complete each side.
   • Install any cross-bracing or stiffeners as specified in the guide.
5. Add half walls
   • Attach half walls to the sides of the enclosure according to the mounting points shown in the instructions.
   • Make sure they are plumb and aligned with the main frame.
6. Raise the assembled structure
   • With helpers, lift the entire wall / ceiling assembly upright into position.
   • Slide it into its final location and double-check clearance to the room walls and ceiling.
7. Level and square the frame
   • Use a level to verify floor contact points and vertical posts.
   • Adjust slightly if needed so the frame is not twisted, which helps the screen hang flat.
8. Install floor panels
   • Starting at the front or back, as specified in the SimBooth guide, lay the full-surface floor panels in order.
   • Make sure panels interlock securely and sit flat with no rocking.
9. Install the hitting mat
   • Place the commercial hitting mat into its intended location, aligning it with the hitting zone marked for IDRA II.
   • Confirm the mat height is flush with the surrounding floor.
10. Mount the impact screen
    • Attach the screen at the top center, then work outwards and down while tensioning evenly.
    • Ensure there are no major wrinkles and that the bottom edge lines up cleanly with the floor edge.
11. Mount IDRA II overhead
    • Attach the IDRA II bracket to the pre-drilled mounting pattern on the enclosure ceiling.
    • Secure the launch monitor to the bracket and route its cables along the frame toward the PC location.
12. Install the projector beam and projector
    • Fix the projector beam / mount to the frame at the recommended distance from the screen.
    • Attach the BenQ AH30ST to the mount, roughly center it, and tighten enough to keep it steady while you fine-tune aim later.
13. Cable management
    • Run power and HDMI to the projector, then run USB / network cables for IDRA II to the PC.
    • Use cable clips, zip ties, or stick-on channels to keep cables off the floor and out of the hitting area.
14. PC and software setup
    • Set your PC display resolution and refresh rate to match the projector’s capabilities.
    • Install GSPro and IDRA II software, then follow their prompts to complete setup and licensing.
15. Calibration and final checks
    • Calibrate screen size, hitting zone, and launch monitor alignment according to IDRA II / GSPro instructions.
    • Hit a series of test shots to verify distances and shot shapes look realistic.
    • Walk the enclosure and verify there are no loose fasteners or trip hazards.

Brochures

Brochures

Videos

Videos

Product Manual and User Guides

Product Manual and User Guides

Technical Drawings

Technical Drawings

YouTube Reviews

YouTube Reviews

FAQ's

Frequently Asked Questions