Description

SimBooth Kit 1

The SimBooth Kit 1 is a turn-key indoor golf simulator kit designed so you can build a premium enclosure, launch monitor, and projector setup in a single self-install package.

It combines a lightweight aluminum structure, full-surface raised floor, crease-free impact screen, and commercial hitting mat with the IDRA II AI overhead launch monitor, BenQ short-throw projector, and GSPro golf simulator software with a 1-year membership.

Kit 1 is sized for typical garages and bonus rooms, with half-walls for protection, low-bounce screen material, and a layout designed to go from delivered pallet to first tee in under a couple of hours for a capable two-person team.

Product Features

Product Features

What's Included

What's Included

• SimBooth Kit 1 enclosure structure
  • Includes aluminum frame, solid black panels, and half-walls.

• Full-surface floor system
  • Includes modular floor panels and integrated hitting mat cut-out.

• Commercial hitting mat
  • Approximately 32" x 54" x 2".

• Impact screen
  • Crease-free, low bounce-back screen design.

• IDRA II AI overhead launch monitor
  • Includes integrated light and required cabling.

• BenQ AH30ST Full HD projector

• Projector beam / mount
  • Designed for structure-mounted projector installation.

• GSPro golf simulator software – 1-Year Membership
  • Auto-renews after year 1 unless cancelled.

• Required cabling
  • Includes HDMI, USB, and power cables.
• Basic hardware and tools for assembly
  • Includes bolts, nuts, washers, wing nuts, and Allen keys.

Product Specifications

Product Specifications

Enclosure & Space Requirements

IDRA II Launch Monitor Key Specs

Projector & PC Requirements Summary

Getting Started Guide

Getting Started Guide

1. Confirm room size and clearance
   • Measure your space against the minimum room requirements and make sure you have swing clearance for your longest club.
2. Unpack the crate
   • Carefully open the 6’ × 4’ × 4’ crate and sort components into groups: structure panels, floor pieces, screen/net, electronics, and hardware.
3. Lay out floor and panels
   • Place floor panels and wall sections near their final positions to visualize orientation before you start bolting pieces together.
4. Assemble the enclosure frame
   • Build the ceiling sections, then connect top and bottom wall panels and install half-walls as shown in the guide.
5. Install screen, net, and floor
   • Stretch the white screen and black impact layer using the integrated Velcro, then install floor panels and hitting mat so everything is flush with the screen.
6. Mount IDRA II and projector
   • Attach IDRA II to the pre-drilled holes at the front center of the ceiling and install the projector beam or ceiling mount, then mount the projector.
7. Connect power, USB, and HDMI
   • Follow the cable diagrams: power and remote switch, USB 3.0 / USB-C from IDRA II to the PC, HDMI from PC to projector, and optional USB hub.
8. Install GSPro and GolfIn launcher
   • On your PC, install the GolfIn launcher, GSPro, and any required IDRA II drivers; log in with your subscription account.
9. Calibrate IDRA II
   • Follow the SimBooth step-by-step calibration instructions using the calibration board to set hitting zone, alignment, and club / ball tracking.
10. Launch your first round
    • Select a course in GSPro, check that shot data appears correctly, and fine-tune projector image and brightness to your liking.

Product Installation Guide

Product Installation Guide

1. Safety and helpers
   • Plan for 4 people, two ladders, and basic tools. Heavy components such as ceiling panels, projector, and IDRA II should be lifted by at least two adults.
2. Assemble the ceiling
   • On the floor, bolt the left, center, and right ceiling panels together using the supplied bolts, washers, and nuts.
3. Attach upper wall panels
   • Fix the left and right top wall panels to the ceiling section.
4. Attach lower wall panels
   • Remove the lower wall fabric covers with Velcro, bolt the bottom wall panels to the top panels, then re-attach the covers.
5. Install scissor bar / roof brace
   • Unfold the scissor bar, lock it with safety pins, and attach it to each side and the center of the ceiling using bolts and wing nuts. This stiffens the structure before lifting.
6. Raise the structure
   • With four people, lift the entire wall / ceiling assembly upright into its final position.
7. Install screen and impact layer
   • Use the Velcro to hang the white screen first, then the black impact net. Make sure the net does not rest on the floor to help keep bounces predictable.
8. Install floor and hitting mat
   • Drop floor sections in the labeled order. Pull the screen under the front bar and attach to Velcro, then install the hitting mat so it sits level with the floor and screen edge.
9. Install half-walls
   • Cut small openings in the carpet where pre-drilled holes are located, insert half-walls, and bolt them to the frame. Re-attach removable lower wall panels with Velcro.
10. Mount IDRA II and elevating bracket
    • Bolt the IDRA II mount through the pre-drilled holes in the center front ceiling panel using the provided hardware, then attach the IDRA II unit to the bracket.
11. Install projector beam and projector
    • Bolt the projector beam to the roof. Optionally use the projector enclosure, then follow BenQ’s instructions to secure the projector and align it to the screen.
12. Route and cover cables
    • Connect power, HDMI, and USB cables and secure them using the supplied wire cover and Velcro straps to keep cables tidy and protected.
13. Finalize projector and PC settings
    • Use NVIDIA Control Panel and Windows display settings to set 1920×1080 or the recommended resolution, adjust aspect ratio, then dial in zoom, keystone, corner fit, and focus.

Brochures

Brochures

Videos

Videos

Product Manual and User Guides

Product Manual and User Guides

Technical Drawings

Technical Drawings

YouTube Reviews

YouTube Reviews

FAQ's

Frequently Asked Questions